바로가기메뉴

본문 바로가기 주메뉴 바로가기

(사)한국터널지하공간학회

ISSN : 2233-8292

Article Contents

Prev Next
e-Submission

Vol.16 No.2
Citation Share

Comparative analysis of cutter acting forces and axial stresses of single and double disc cutters by linear cutting tests

(사)한국터널지하공간학회 / (사)한국터널지하공간학회, (P)2233-8292; (E)2287-4747
2014, v.16 no.2, pp.181-191
https://doi.org/10.9711





& (2014). Comparative analysis of cutter acting forces and axial stresses of single and double disc cutters by linear cutting tests. (사)한국터널지하공간학회, 16(2), 181-191, https://doi.org/10.9711
  • Downloaded
  • Viewed
PDF Download

Abstract

This study aims to evaluate cutter acting forces as well as axial stresses and torques in the shaft of two kinds of disc cutters including a single disc cutter and a double disc cutter with the same cutter ring geometry in a series of linear cutting tests. From the tests, the mean values of normal forces and rolling forces acting on the double disc cutter were approximately twice as high as those from the single disc cutter. Similarly, the mean values of axial stresses in the shaft of the double disc cutter were also twice as high as those from the single disc cutter even though the comparisons of torques from two kinds of disc cutters were insignificant since they showed very low values. However, it is necessary to take the durability of a tapered roller bearing used for the double disc cutter into high consideration since the average normal force from the double disc cutter exceeds the allowable force for a disc cutter with the diameter of 432 mm (17 inches). Finally, there is no practical problem in terms of axial stresses in the shaft of the double disc cutter since they are much lower than the yielding stress of the cutter shaft material, even though the axial stresses in the shaft of the double disc cutter are approximately twice as high as those from the single disc cutter.

keywords
선형절삭실험, 더블디스크커터, 커터작용력, 축응력, 토크, Linear cutting test, Double disc cutter, Cutter force, Axial stress, Torque

Reference

1.

1. Balci, C., Tumac, D. (2012), “Investigation into the effects of different rocks on rock cuttability by a V-type disc cutter”, Tunnelling and Underground Space Technology, Vol. 30, pp. 183-193.

2.

2. Bilgin, N., Balci, C., Tunςdemir, H., Eskikaya, Ş, Akgül, M., Algan, M. (1999), “The Performance Prediction of A TBM in Difficult Ground Condition”, AFTES-Journeesd’Etudes Internaltionales de Paris:, pp. 115-121.

3.

3. Chang, S.H., Choi, S.W., Lee, G.P., Bae, G.J. (2011), “Rock TBM design model derived from the multi-variate regression analysis of TBM driving data”, Journal of Korean Tunnelling and Underground Space Association, Vol. 13, No. 6, pp. 531-555.

4.

4. Chang, S.H., Choi, S.W., Park, Y.T., Lee, G.P., Bae, G.J. (2012), “Characterization of the deformation of a disc cutter in linear rock cutting test”, Journal of Korean Tunnelling and Underground Space Association, Vol. 14, No. 3, pp. 197-213.

5.

5. Chang, S.H., Choi, S.W., Park, Y.T., Lee, G.P., Bae, G.J. (2013), “Experimental evaluation of the effects of cutting ring shape on cutter acting forces in a hard rock”, Journal of Korean Tunnelling and Underground Space Association, Vol. 15, No. 3, pp. 225-235.

6.

6. Choi, S.W., Chang, S.H., Park, Y.T., Lee, G.P., Bae, G.J. (2013), “An Experimental study on the loads and temperature acting on the shaft of a disc cutter during linear rock cutting test”, Journal of Korean Tunnelling and Underground Space Association, Vol. 15, No. 3, pp. 237-251.

7.

7. Entacher, M., Winter, G., Bumberger, T., Decker, K., Godor, I., Galler, R. (2012), “Cutter force measurement on tunnel boring machines-System design”, Tunnelling and Underground Space Technology, Vol. 31, pp. 97-106.

8.

8. Gertsch, R., Gertsch, L., Rostami, J. (2007), “Disc cutting tests in colorado red granite: Implications for TBM performance prediction”, International Journal of Rock Mechanics & Mining Sciences, Vol. 44, pp. 238-246.

9.

9. KS (2007), Cr-Mo Steel (KS D 3711:2007), KS.

10.

10. KTA (2008), Series of tunnel engineering 3–mechanized tunneling technology-design, Korean Tunneling Association, CIR, pp. 261.

11.

11. Ozdemir, L., Nilsen, B. (1993), “Hard rock tunnel boring prediction and field performance”, Rapid Excavation Tunneling Conference (RETC) Proceedings, Boston, USA.

12.

12. Rostami, J., Ozdemir, L. (1993) “A new model for performance prediction of hard rock TBMs”, Proceedings of Rapid Excavation and Tunneling Conference (RETC), Boston, 13-17 June, pp. 793-809.

13.

13. Rostami, J. (1997), “Development of a force estimation model for rock fragmentation with disc cutters through theoretical and physical measurement of crushed zone pressure”, Ph.D Dissertation, Colorado School of Mines, Golden, Colorado, pp. 68-69.

14.

14. Rostami, J. (2013), “Study of pressure distribution within the crushed zone in the contact area between rock and disc cutters”, International Journal of Rock Mechanics & Mining Sciences, Vol. 57, pp. 172-186.

15.

15. Snowdon, R.A., Ryley, M.D., Temporal, J. (1982), “A study of disc cutting in selected british rocks”, Int. J. Rock Mech. Min. Sci. & Geomech. Abstr., Vol. 19, pp. 107-121.

(사)한국터널지하공간학회

e-Submission OA Policy