초록

본 논문에서는 굴착공법이 터널변위 거동에 미치는 영향에 대한 내용을 다루었다. 먼저 비교적 동일한 시공조건을 대상으로 중벽분할 굴착공법과 링컷공법을 비교하여 각 굴착공법에 따른 터널거동 메카니즘을 고찰하는데 초점을 두었다. 이를 위해 3차원 유한요소해석을 수행하였으며, 각 공법별 해석결과로부터 막장 안정, 천단침하, 지표침하, 숏크리트 라이닝의 응력을 비교하였다. 전반적으로 중벽분할 공법을 적용할 경우 굴진과정에서 터널변위 제어에 탁월한 효과가 있는 것으로 나타났으며, 링컷공법 적용 시 지표침하 억제 효과에 보다 효율적인 것으로 나타났다. 본 연구결과를 종합하여 설계 시 고려하여야 할 주안점을 제시하였다.

Abstract

This paper presents the effect of excavating methods on tunnel behavior. As part of this study, it is preliminarily focused on the comparison of two different excavation methods, center diaphram (CD) method and ringcut (RC) method. Especially, the purpose of this research is to study the behavioral mechanism of two tunnels which share the same construction environment but different excavating method. Two numerical analysis models with the same tunnel section and material properties are compared in this study, and they are analyzed by 3D finite element analysis. In each model, face stability, crown displacement, ground settlement, and shotcrete-lining stress are computed, then the general behavior of CD method and RC method is studied. The results indicate that the CD method tends to be effective in controlling tunnel displacement while the RC method is more effective in controlling ground settlement. Design implications of the findings from this study are discussed.

초록

본 논문에서는 운영중인 터널에 인접하여 신설터널이 시공되는 경우 터널간 상대적인 위치관계에 따른 기존터널의 라이닝에 미치는 영향에 대한 내용을 다루었다. 신설터널이 인접하여 시공되는 조건에 대해 2차원 및 3차원 유한요소해석을 통해 매개변수 연구를 수행하여, 신설터널의 상대적 위치 및 굴진에 따른 기존터널 라이닝의 유발된 단면력과 변형형상의 변화경향을 분석하였다. 신설터널은 기존터널의 상부 또는 하부에 시공되는 경우 그 영향이 가장 크게 작용하는 것으로 나타났으며 측벽방향으로 수평하게 시공되는 조건이 가장 안정적으로 분석되었다. 한편 기존터널과 교차하여 시공되는 경우 기존터널의 상부보다 하부에 신설터널이 시공될 때의 영향이 더 큰 것으로 나타났다.

Abstract

Effects of new tunnel construction on an existing tunnel are investigated in this paper. A parametric study was conducted on a number of conditions in terms of relative location of the new tunnel to the existing tunnel using 2D and 3D finite element models. The results indicated that the new tunnel construction imposes most severe effect on the existing tunnel's lining when located below the existing tunnel's springline for cases in which the new tunnel is constructed parallel to the existing tunnel. It is also revealed that the effect to the new tunnel construction is larger when the new tunnel is constructed under the existing tunnel than above for cases in which the new tunnel is crossed with the existing tunnel. Practical implications of the finding are discussed.

초록

Abstract

Understanding the airflow characteristics within the canopy structure installed between closely adjacent tunnels either for light adaptation or for protection from snow hazards is required for the normal ventilation as well as safety system design. Grade, horizontal alignment, cross-sectional area and shape are known to substantially influence the fire smoke behavior and their influences raise great concern for the safety design. This paper aims at studying the effects of tunnel geometrical characteristics and canopy installation on the ventilation and fire propagation through CFD analysis. In the case of 145m long canopy, 50% opening ratio is preferred with respect to the airflow pattern and ventilation efficiency. When a 20MW fire occurs in a 1.8km-long tunnel and four 1250mm reversible jet fans are instantly turned on, smoke concentration at 40m downstream of the fire decrease 13% for the upgrade tunnel with 2% gradient and increases 20% for -2% gradient, compared to the standard horizontal tunnel. Backlayering is observed within 45m-long segment toward the entrance in 2% down-graded tunnel. In a rectangular tunnel, there is no significant difference of smoke concentration as well as velocity profile from the standard crown tunnel. Three-laned tunnel shows lower level of both profiles and backlayering is detected up to 50m upstream of the fire, while the risky situation rapidly disappears thereafter.

초록

Abstract

The domestic standards which used the standards of Road Association of Japan standards presents the distances of between jet-fans by the caliber of jet-fan. However, the Permanent International Association of Road Congress (PIARC) encourages it to be ten times a diameter of the tunnel. The distance of jet-fans installed in bases of two standards differs as much as two times, as so the proper basis after analysis of internal air current is needed since such difference can lead to disadvantage for selection of ventilation configuration. Based on Froude modeling theory, 1/40 scale acrylic model of a tunnel (215mm in diameter and 6.9m in length) and jet-fan (26.3mm and 31.6mm in caliber) was made for the measurement of changes in pressure and velocity due to the extension of tunnel for analysis of internal air current. And we measured the changes in pressure of surroundings of a jet-fan for confirmation of recirculation due to the exterior airs when the jet-fan is on. The results of the model test show that internal air current was not influenced by the caliber of jet-fan and its changes in pressure and velocity were stable in the point where it was nine times of diameter of the tunnel. Also the recirculation when the jet-fan is on could be verified. According to such results, in the cases of installing jet-fan in tunnels, the distances between jet-fans needs to be more than nine times the diameter.

초록

막장볼트는 시공중 지반조건 및 천공기계의 기계적 원인에 의해 수평으로부터 벗어나게 타설되는 경우가 많다. 본 연구는 실내실험과 수치해석을 통하여 막장볼트가 수평으로부터 벗어나는 경우에 대한 보강효과의 변화를 검증하였다. 또한 이 결과를 바탕으로 추가해 주어야 하는 볼트의 개수에 대하여 고찰하였다. 본 연구로부터 막장 중앙부부터 타설하는 막장볼트는 가능한 한 수평으로 타설하는 것이 효과적이며 벗어나는 경우에는 볼트를 추가해 주어야 하는 것이 명확해 졌다. 본 연구의 조건하에서는 3본/단면을 타설 할 경우 모든 볼트가 R15°로 수평으로부터 벗어나면 1.5본/단면을 추가해 주어야 하는 것으로 나타났다.

Abstract

During installation of face bolts, they are often deviated from the designed horizontal direction. In this study, a laboratory test and numerical analysis were conducted to examine the change of support effect by them. Also, the number of bolts to be added for achieving the designed support effect was considered. It was verified in this study that the horizontal installation is more effective. Under the test condition of this study, 1.5 bolts/section should be added in the face of which the installation density was 3 bolts/section when the bolts were installed with R15° angle from the horizontal position.

초록

본 연구에서는 연약한 지반에 속하는 모래지반과 풍화토가 터널상부에 존재하며 연암층에 위치하는 해저터널을 대상으로 터널 배면의 간극수압이 터널의 안정성에 미치는 영향을 분석하였다. 이를 위해 비배수 조건과 배수조건을 가정하여 연계해석을 수행하였다. 비배수 터널의 경우에도 숏크리트 두께를 달리하여 안정성을 비교하였으며, 배수 터널의 경우는 숏크리트의 투수계수와 공극률을 달리하여 민감도분석을 수행하였다. 해저터널의 안정성은 유광호 등(2000, 2001, 2005)에 의해 제안된 전단강도감소 기법을 사용하여 수치적으로 구해지는 안전율을 사용하였다. 본 연구에서는 수리-역학적 연계해석 시 시공단계별 정상류 상태를 먼저 재현하고 터널의 안전율을 구했다. 연구결과 터널내로의 지하수 유입량을 어느 정도 허용함으로써 오히려 터널의 안정성이 높아짐을 확인할 수 있었다.

Abstract

In this study, it was analyzed how the pore pressure behind a subsea tunnel influences on the stability of the tunnel. The tunnel is located in the soft rock layer, and a soft sandy layer and weathered soil layer are located on the top of it. Coupled numerical analyses are performed for both drained and undrained condition with varying coefficients of lateral earth pressure. In the case of undrained conditions, the stability of the tunnel was analyzed with different thicknesses of shotcrete. On the other hand, a sensitivity analysis was performed with different hydraulic conductivities and porosities of the shotcrete for the drained conditions. The stability of a subsea tunnel was evaluated in terms of safety factor suggested by You et al.(2000, 2001, 2005) based on the shear strength reduction technique. In this paper, the safety factor of a tunnel was calculated under steady state flow condition during hydro-mechanical coupled analysis. As a result, it was found that the stability of a subsea tunnel could be rather increased by allowing a proper amount of groundwater inflow into a subsea tunnel.

초록

Abstract

The structural analysis for the secondary lining of tunnels is generally performed by a frame analysis model. This model requires a ground loosening load estimated by some empirical methods, but the load is likely to be subjective and too large. The ground load acting on the secondary lining is due to the loss of the supporting function of the first support members such as shotcrete and rockbolts. Therefore, the equilibrium condition of the ground and the first support members should be considered to estimate the ground load acting on the secondary lining. Ground-lining interaction model, shortly GLI model, is developed on the basis of the concept that the secondary lining supports the ground deformation triggered by the loss of the support capacity of the first support members. Accordingly, the GLI model can take into account the ground load reflecting effectively not only the complex ground conditions but the installed conditions of the first support members.The load acting on the secondary lining besides the ground load includes the groundwater pressure and earthquake load. For the structural reinforcement of the secondary lining based on the ultimate strength design method, the factored load and various load combination should be considered. Since the GLI model has difficulty in dealing with the factored load, introduced in this study is the superposition principle in which the section moment and force of the secondary lining estimated for individual loads are multiplied by the load factors. Finally, the design method of the secondary lining using the GLI model is applied to the case of a shallow subway tunnel.

초록

구조물은 시공과 더불어 노화 현상이 발생하는데 해당 구조물의 효율적인 사용을 위해서는 주기적인 점검 및 유지보수가 수행되어야 한다. 적절한 유지보수의 시기 및 방법의 결정에 있어서는 사전 점검이 중요한 역할을 한다. 본 연구에서는 터널의 사전점검 자동화를 위한 검측 시스템의 개발을 목표로 하고 있으며 이를 위한 사전단계로 시작품을 제작하였다. 시작품 제작에 앞서 기존의 영상 및 레이저를 기반으로 하는 터널 스캐너를 비교 분석하였으며 초기 단계의 터널 스캐너 시작품을 제작하였다. 레이저 스캐닝 시스템 제작에 앞서 범용의 근거리 측량용 상용 레이저 스캐너를 통하여 레이저 스캐너의 적용성을 확인하였으며 그 결과로부터 레이저 스캐너를 바탕으로 하는 터널 스캐닝 시스템이 제작되었다. 제작된 시스템을 바탕으로 실제 공용중인 여러 형상 및 크기의 터널에 대한 스캐닝이 수행되어 장비의 검증이 이루어 졌다.

Abstract

Most structures experience deterioration after construction. A routine inspection and maintenance must be accomplished for the efficient use of the structures. The routine inspection will play a major role on the determination of maintenance period and method. This study aims development of an automated tunnel inspection system based upon a 3 dimensional laser scanner. As for the initial stage of the project, a prototype tunnel scanner has been developed. The development of a tunnel scanner prototype follows comparison between image scanning and laser scanning system and investigation on the applicability and adaptivity of the scanners to the railway tunnel scanner. The applicability of the laser scanner on the railway tunnel has been confirmed from the pilot test by using commercialized general purpose close range laser scanner and applicability of a laser scanner as a railway tunnel scanner has been checked. From the result, a prototype of railway tunnel scanner has been built and the calibration of the system was carried out. Finally the developed tunnel laser scanner has been applied to different shapes and sizes of tunnels in use.