open access
메뉴
open access
메뉴
ISSN : 0376-4672
Recently, there has been an increasing interest in the regulation of medical & dental profession in South Korea due to various medical scandals & exacerbated commercialism. Consequently, the voice asking for strengthening the license management of medical & dental profession is rising. However, there is an absolutely lacking discussion on self-regulation of the Korean dentist community. This study investigated International Society of Dental Regulators and dental regulatory authorities in the U.K., Ontario in Canada, California in the U.S. and Australia. In addition, this study examined what situations Japan was in, which was similar to Korea in terms of systems. In the U.K., the U.S., Canada and Australia, there are independent dental regulatory authorities, which place emphasis on lay personnel participation. In addition, the organizations prepared very specific and detailed ethics, standards, and punishment guidelines to be followed by professionals. And, various efforts are being made to secure transparency and trust. As a result of this study, self-regulation in Korea seems to require an open approach that embraces civil society, and it is considered that dentist should lead social discussion more positively.
Atrophic alveolar ridge of maxillary anterior area is commonly observed after the extraction of teeth in patients with severely compromised periodontal disease, causing difficulties with implant placement. Successful esthetics and functional implant rehabilitation rely on sufficient bone volume, adequate bone contours, and ideal implant positioning and angulation. The present case report categorized the ridge augmentation techniques using guided bone regeneration (GBR) on the maxillary anterior site by Seibert classification. Case I patient presented for implant placement in the position of tooth #11. The alveolar ridge was considered a Seibert classification I ridge defect. Simultaneous implant placement and GBR were performed. Eight months after implantation, clinical and radiological examinations were performed. Case III patient presented with discomfort due to mobility of the upper maxillary anterior site. Due to severe destruction of alveolar bone, teeth #11 and #12 were extracted. After three months, the alveolar ridge was considered a Seibert classification III ridge defect. A GBR procedure was performed; implantation was performed 6 months later. Approximately 1-year after implantation, clinical and radiological examinations were performed. During the whole treatment period, healing was uneventful without membrane exposure, severe swelling, or infection in all cases. Radiographic and clinical examinations revealed that atrophic hard tissues and buccal bone contour were restored to the acceptable levels for implant placement and esthetic restoration. In conclusion, severely resorbed alveolar ridge of the maxillary anterior area can be reconstructed with ridge augmentation using the GBR procedure so that dental implants could be successfully placed.
Composite resin restorations in posterior teeth are increasing due to the aesthetic needs of patients and the development of materials. This trend will accelerate in line with domestic insurance policies. However, resin composites generate stresses due to their contraction during the polymerization process. To reduce the polymerization shrinkage stress of resin composites, incremental layering technique has been recommended for decades. This technique reduces stress at the cavity wall interface and allows a more efficient light curing of the material. Bulk-fill resin composites have been designed to simplify the restorative technique because they can be placed into cavities in a single increment of 4-5mm. The simplification of the operative procedures is desirable in clinical daily practice. In this context, bulk-fill resin composites are an attractive alternative for posterior restorations. However, a clearer understanding of the clinical performance of this relatively new class of materials in comparison to conventional resin composites is required. Based on previous studies, the aim of the current review was to present the clinical criteria for the use of bulk-fill composites in direct restorations of posterior teeth.
The rapid evolution of CAD/CAM (Computer Aided Design / Computer Aided Manufacture) led to a dramatic impact on all disciplines of dentistry especially in the fields of prosthodontics and restorative dentistry. This article is to examine the history, advantages & disadvantages and some clinical considerations of CAD/CAM restoration.
Increasing the aesthetic needs of patients and decreasing the use of amalgam had led to increased demand for dental resin composite. Thereby, light curing unit (LCU) has become an essential equipment in dental clinic. To ensure long-term prognosis of photopolymerized materials, LCU should have a uniform and consistent radiant output and an emission spectrum that includes the active wavelength range of photoinitiators. In addition, when the correct use and thorough maintenance and repair of LCU are performed, the higher success rate of restoration using photopolymerization materials will be achieved.